设为首页 设为收藏

联系方式

 

洛阳松导感应加热科技有限公司 

联系方式:15038554363  

24小时技术热线:15038554363

电 话:0379—60125771

邮 箱:1390003299@qq.com

厂址:河南省洛阳市洛新工业园区

  • 产品
  • 1T中频熔炉

    2T中频熔炉

    5T中频熔炉

    中频熔炉

    中频感应炉

    250kg中频感应炉 ,

    250kg中频感应炉

    500kg中频感应炉

    1T中频感应炉

    2T中频感应炉

    5T中频感应炉

    3T中频感应炉

    全自动石墨喷温锻造感应加热设备

    圆棒,圆钢中频感应加热设备

    中频钨钼烧结炉

    中频感应烧结炉

    钼丝钼块烧结炉

    钢管感应加热炉

    圆钢感应加热炉

    350kW铝圆棒中频感应自动加热生产线

    Φ65mm圆钢中频锻造炉

    300KW中频感应加热设备

    铜棒中频感应加热炉

    Φ70mm圆钢感应加热炉

    电机端环中频钎焊设备

    钻杆端部加热设备

    3T 感应熔炼炉

    30t感应熔炼炉

    中频炉技术资料
    分享到:
        本文为技术资料或者文章来自网络,仅供参考学习,如涉嫌侵权,请告知删除
        

    3T中频熔炼炉的安装和维护

    13T中频熔炼炉拆箱后,首先检查各电器元件在运输过程中是否有损坏,所有紧固零件是否有松动或脱落,如果有上述情况发生应及时修复和紧固。

    23T中频熔炼炉应安装在通风良好,不受雨水侵袭的室内。机体与墙壁应保持一定的距离,以便机体前后左右门能正常开启。

    3进出水路由用户连接; 进出水各用两路,进水口管径为1.5英寸 ;出水口的管径为2英寸。

    4用户选择操作方便的位置安装与外操作台,机体与外操作台气缸之间均对号连接。

    5冷却水质应比较纯净;电阻率不小于2.5KΩ. CM(在温度25℃左右测量);PH值在69之间。                                                                                                                                                                                         

    63T中频熔炼炉应每月检查一次,清除机内尘埃,如发现损蚀、松动等现象应予修复后再使用。

    73T中频熔炼炉需停用一段时间,则应清除冷却水路中的积水,并加强通风干燥,以免装置受潮引起元件损坏。

    8熔断器熔断后,应换上同型号的熔断器。

    1.After unpacking the 3T medium frequency melting furnace, first check whether the electrical components are damaged during transportation, and whether all the fastening parts are loose or fall off. If any of the above occurs, repair and tighten them in time.

    2. 3T medium frequency melting furnace should be installed in a well ventilated room that is not affected by rain. The body and the wall should be kept at a certain distance so that the front, rear, left and right doors of the body can be opened normally.

    3. the inlet and outlet water route user connection; the inlet and outlet water use two ways, the inlet diameter is 1.5 inches; the outlet diameter is 2 inches.

    4. The user selects the convenient installation position and the external operation console, and the machine body and the external operation console cylinder are connected to each other.

    5, the cooling water quality should be relatively pure; the resistivity is not less than 2.5KΩ. CM (measured at a temperature of about 25 ° C); PH value is between 6 and 9.

    6, 3T medium frequency melting furnace should be inspected once a month to remove dust inside the machine. If damage or looseness is found, it should be repaired before use.

    7.  If the 3T intermediate frequency melting furnace needs to be deactivated for a period of time, the accumulated water in the cooling water circuit should be removed and the ventilation and drying should be strengthened to avoid damage to the components caused by moisture in the device.

    8.  After the fuse is blown, replace it with a fuse of the same type.


    Copyright© 2007-2013洛阳松导感应加热科技有限公司 All Rights Reserved 
    电 话:0379—60125771 手 机:15038554363
    网站正在制作中,随时修改,非正式运行。